Gear lever spring washer, for Citroen 2CV
This disk is mounted with the connection by the gear lever interior onto the gear lever to the gearbox.
Search in Citroen-2CV-Mehari for
1612 Articles | Page 26 of 33
Gear lever: M7 screw, for the clip (gearstick on the gearbox)
Inclusive nut and disks. Suitable for Citroen 2CV6, 2CV4, Dyane, Mehari, AK.
Gear levers pin, for the gear lever connection with the shifter rod rubber
Suitable for Citroen 2CV. Measurement: 6x20mm. Or.Nr.: A334-57 (18063)
Gear lever link (sheet metal), 90° twists
connection of the gear lever in the interior on gear lever on the gearbox. (without rubbers). Suitable for Citroen 2CV.
Gear lever guide from synthetic
The sleeve leads the gear lever in the guide tube. Suitable for 2CV. Or.Br. A334-81A.
Discs (windscreen) Pull-in tool (cord with handle)
This is used to pull the rubber lip of the seal over the sheet metal fold. Very helpful!
Windscreens (windscreen) piping assembly tool - bracket inserts
For small piping. There are 5 brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
Windscreen Installation Tool Set. Windshield sealing trim assembly tool
With this tools will the rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
Permanently elastic window sealant. Original Teroson! 75ml tube. Application
Ideal for sealing rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
Vehicle Window sealant permanent elastic. Original Teroson! Cartouche 310ml
Application: Ideally to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
Washer reservoir with integrated, electrical water pump. 12 V. Capacity: 1.2 L
width: 122mm, overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
Washer reservoir, rubber bushing above in the cap (for the hose)
Suitable for Citroen DS, HY, 2CV etc. dimension: 5 x 18 x 4mm.
Wiper system nozzle - lower part, from brass. Suitable for Citroen DS, HY
2CV etc.. Mounting diameter: 6,0mm.
Wiper nozzle synthetic grey. Universal fitting. 4mm hose connection
The wiper nozzle is locked with a nut from rear. 1 water jet. Low body height. Mounting diameter: 8,0mm.
Wiper nozzle cleaning and adjustment tool! Sturdy adjustment point
light cleaning stick. Both ends with end cap.
Wiper nozzle chromium-plates. Universal fitting. 4mm hose connection
The wiper nozzle is locked with a nut from rear. 2x water jet. The nozzles are individually adjustable! Mounting diameter: 8,0mm.
Wiper system nozzles - lower part, from brass
With additional connection for a hose. Suitable for Citroen DS, to year of construction 1969. In addition, this additional connection is very practical for Citroen DS, HY etc.. Mounting hole: 6,0mm.
Washer pump electrical. 12 V. Very stable version with galvanized metal fixture
2x flat plug connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
Foot-operated pump set for windschield wiper fluid. Consisting of foot pump
2 return flow stoppers, 1x T-valve, 3 meters hose. Assembly: Starting from the foot pump with the T-valve, 1x to the reservoir (place the valve in such a way that the water from the reservoir can pass through) and 1x to the windshield washer nozzle (valve lets the water pass in the direction of the nozzle). The flow directions are marked with an arrow on the valve. Assembly instruction online in the shop.
PDF FILE
Disk washing water hand pump, reproduction, 5mm
This pump is mounted in the dashboard. In addition, the pump is a reproduction of the first version, and can installed into a Citroen 2CV6 and partial in a Renault R4 .
Windscreen washing water hand pump. Reproduction
completely with sheet metal holder for a later mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
Disks washing water return stop (valve). Connection: 5mm
This valve is an genuine improvement for classical vehicles, which pump the water by a hand pump. Please observe flow direction when assembling!
Windscreen washer fluid reservoir, universal. The set is supplied with
Washer reservoir, electric pump, 2x washer nozzles with 2 jets, electric button, installation material. The washer reservoir can be pulled out of its holder. Very good set for retrofitting or conversion. Our recommendation. 12 volt. The washer tank can be retrofitted to many vehicles. E.g. Renault R4, R5, Citroen 2CV, HY, DS, Peugeot 404, 504 etc. Water tank dimensions (overall): Width: 12.5cm. Depth: 11cm. Height: 19.5cm.
Wiper arm black, suitable for Mehari. Reproduction. Length 31cm
from centre axle mounting on vehicle to centre axle wiper blade mounting)
Windshield wiper linkage retaining ring
For the securement of the wiper linkage at the wiper axle. Suitable for Citroen 2CV.
Hose air circulation for the disc brake in front. Suitable for bad copied
French air circulations. (not suitable for our number 13020 + 13021). Citroen 2CV. 35mm inside diameter, 250mm long.
Hose air circulation for the disc brake in front. Suitable for Citroen 2CV6
Dyane, Mehari. Accurate reproduction from synthetic, as the original hoses. Inside diameter 40-42mm, length 235mm.
Hose clamp 11-17mm, especially for radiator hose. Vintage look
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 13-20mm, especially for radiator hose. Vintage look
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 15-24mm, especially for radiator hose. Vintage look
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 19-28mm, especially for radiator hose. Vintage look
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 22-32mm, especially for radiator hose. Vintage look
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Screw for the driving shaft to the drive shaft. Gearbox side Installed
Suitable for Citroen for 2CV to year of construction 1971. Or.Nr.: AM451-94A
Screw for the securement of the speedometer cable in the gearbox. (M7x50mm)
Suitable for Citroen 2CV, Dyane, Ami, Mehari.
1612 Articles | Page 26 of 33
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
