Gear lever spring washer, for Citroen 2CV
This disk is mounted with the connection by the gear lever interior onto the gear lever to the gearbox.
This disk is mounted with the connection by the gear lever interior onto the gear lever to the gearbox.
Inclusive nut and disks. Suitable for Citroen 2CV6, 2CV4, Dyane, Mehari, AK.
Suitable for Citroen 2CV. Measurement: 6x20mm. Or.Nr.: A334-57 (18063)
connection of the gear lever in the interior on gear lever on the gearbox. (without rubbers). Suitable for Citroen 2CV.
The sleeve leads the gear lever in the guide tube. Suitable for 2CV. Or.Br. A334-81A.
This is used to pull the rubber lip of the seal over the sheet metal fold. Very helpful!
For small piping. There are 5 brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
With this tools will the rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
Ideal for sealing rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
Application: Ideally to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
width: 122mm, overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
Suitable for Citroen DS, HY, 2CV etc. dimension: 5 x 18 x 4mm.
2CV etc.. Mounting diameter: 6,0mm.
The wiper nozzle is locked with a nut from rear. 1 water jet. Low body height. Mounting diameter: 8,0mm.
light cleaning stick. Both ends with end cap.
The wiper nozzle is locked with a nut from rear. 2x water jet. The nozzles are individually adjustable! Mounting diameter: 8,0mm.
With additional connection for a hose. Suitable for Citroen DS, to year of construction 1969. In addition, this additional connection is very practical for Citroen DS, HY etc.. Mounting hole: 6,0mm.
2x flat plug connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
2 return flow stoppers, 1x T-valve, 3 meters hose. Assembly: Starting from the foot pump with the T-valve, 1x to the reservoir (place the valve in such a way that the water from the reservoir can pass through) and 1x to the windshield washer nozzle (valve lets the water pass in the direction of the nozzle). The flow directions are marked with an arrow on the valve. Assembly instruction online in the shop.
This pump is mounted in the dashboard. In addition, the pump is a reproduction of the first version, and can installed into a Citroen 2CV6 and partial in a Renault R4 .
completely with sheet metal holder for a later mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
This valve is an genuine improvement for classical vehicles, which pump the water by a hand pump. Please observe flow direction when assembling!
Washer reservoir, electric pump, 2x washer nozzles with 2 jets, electric button, installation material. The washer reservoir can be pulled out of its holder. Very good set for retrofitting or conversion. Our recommendation. 12 volt. The washer tank can be retrofitted to many vehicles. E.g. Renault R4, R5, Citroen 2CV, HY, DS, Peugeot 404, 504 etc. Water tank dimensions (overall): Width: 12.5cm. Depth: 11cm. Height: 19.5cm.
from centre axle mounting on vehicle to centre axle wiper blade mounting)
For the securement of the wiper linkage at the wiper axle. Suitable for Citroen 2CV.
French air circulations. (not suitable for our number 13020 + 13021). Citroen 2CV. 35mm inside diameter, 250mm long.
Dyane, Mehari. Accurate reproduction from synthetic, as the original hoses. Inside diameter 40-42mm, length 235mm.
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Embossed band with raised edges. This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Suitable for Citroen for 2CV to year of construction 1971. Or.Nr.: AM451-94A
Suitable for Citroen 2CV, Dyane, Ami, Mehari.